Bildegalleri
(1/8)
Filament extruder 3d printer
Til salgs
Fiks ferdig
200 kr
Frakt fra 39 kr + Trygg betaling 39 kr
Trygg handel med Fiks ferdig
Varen sendes til deg, og du har 24 timer til å inspisere den før pengene overføres til selgeren.
Beskrivelse av varen
Tilstand: Pent brukt - I god stand
Prusa 3 sender raskt
Prusa MK3 same as Wanhao 3d printer
Short answer: No — they are not the same, but they are related.
🧩 Why they seem similar
Both the Original Prusa i3 MK3 and many Wanhao printers (like the Wanhao Duplicator i3) come from the same open-source “Prusa i3” design.
The Wanhao is basically a cheap clone / derivative of that design.
👉 That’s why they look almost identical (same frame style, moving bed, etc.).
⚙️ Key differences (important)
1. Quality & reliability
Prusa MK3 → high-end, very reliable, “just works” machine with consistent results
Wanhao i3 → budget printer, often needs tuning and upgrades
From real users:
“Going to the Mk3 was a huge upgrade… freed up so much time”
2. Features
Prusa MK3
Auto bed leveling
Filament sensor
Power-loss recovery
Crash detection
Magnetic removable bed
Wanhao i3
Basic features
Usually no auto leveling (unless upgraded)
3. Build quality
Prusa → better components, tighter tolerances
Wanhao → cheaper parts, more vibration/flex issues
4. Software & ecosystem
Prusa
Excellent firmware + slicer (PrusaSlicer)
Strong support and updates
Wanhao
Minimal support
More DIY/troubleshooting
5. Price
Prusa MK3 → expensive (~$700–1000 range historically)
Wanhao i3 → cheap entry-level (~$200–400 range)
🧠 Simple way to think about it
Wanhao i3 = “budget clone of Prusa design”
Prusa MK3 = “refined, premium original version”
✅ Bottom line
They are:
✔️ Based on the same concept
❌ Not equal in performance or experience
👉 If you want plug-and-play reliability → Prusa
👉 If you don’t mind tinkering and upgrading → Wanhao
If you want, tell me your budget and what you want to print—I can suggest better modern alternatives too (there are much better options today than both).
is extruder the same
Short answer: No — the extruders are not the same, even though they do the same job.
🔧 What they share
Both the Original Prusa i3 MK3 and typical Wanhao i3 printers:
Use a direct drive extruder (motor sits on the print head)
Feed standard 1.75 mm filament
Combine extruder + hotend in one assembly
👉 So functionally similar, but the design and performance differ quite a bit.
⚙️ Key differences
🟠 Prusa MK3 extruder
Custom-designed (Bondtech-style gears)
Dual-drive gears → grips filament from both sides
Integrated filament sensor
Better cooling & airflow design
Optimized for flexible filaments (TPU, etc.)
👉 Result: more reliable feeding, fewer jams, better print quality
🔵 Wanhao i3 extruder
(often on models like Wanhao Duplicator i3)
Simpler, cheaper design
Usually single drive gear
Less precise tension control
Weaker cooling setup
👉 Result:
Can slip or grind filament
Struggles more with flexible materials
Often upgraded by users
🧠 Real-world difference
Prusa: “set it and forget it”
Wanhao: “tune it, maybe upgrade it”
A lot of Wanhao owners actually replace their extruder with:
Bondtech upgrade
E3D extruder setups
✅ Bottom line
❌ Not the same hardware
✔️ Same basic concept (direct drive extruder)
⭐ Prusa’s extruder is significantly more advanced and reliable
If you're comparing for upgrades or repairs, tell me your exact Wanhao model—I can tell you which Prusa parts (if any) are actually compatible.
NB: Knappen for å vise hele beskrivelsen har kun en visuell effekt.
Brukerprofil
Du må være logget inn for å se brukerprofiler og sende meldinger.
Logg innAnnonsens metadata
Sist endret: 17.3.2026 kl. 22:32 ・ FINN-kode: 455689621
Utforsk våre nye sider for klær og mote
Ta en titt
