Fiks ferdig
Bildegalleri
(1/2)
Rigblaster PRO Interfacekort mellom PC og Transceiver selges
Til salgs
Fiks ferdig
1 500 kr
Frakt fra 119 kr + Trygg betaling 107 kr
Trygg handel med Fiks ferdig
Varen sendes til deg, og du har 24 timer til å inspisere den før pengene overføres til selgeren.
Beskrivelse av varen
Tilstand: Pent brukt - I god stand
Her har du muligheten til å få tak i en ubrukt skjeldenhet.
Rigblaster PRO er et lydkort med masse funksjoner som kan kobles opp med to transceivere på en gang.
Her er alt i original emballasje med alle papirer og CD med masse software.
Her er litt produsenten skriver om egenskaper:
Capabilities
Compatible with All Manufacturers' Radios
Can be used with almost any make or model microphone and most model radios no matter what brand
Any radio that has a 8 pin round screw on microphone connector
Any radio that has an RJ45 modular telephone style connector
Any radio with RJ25 6 wire microphone connector with the purchase of an optional FT100 style 6 wire modular mic. cable
Any radio with 4 pin round microphone connector with the purchase of a optional 4 pin mic cable
Computer Interface
Built-in Rig Control
Built in rig control, RS232 to TTL interface tested with Icom and Yaesu; compatible with Ten Tec
Rig control is possible along with sound card PTT control and CW keying on a SINGLE serial port using Hamscope or MixW software
Rig control, FSK keying and sound operation is supported using two serial ports or when using two separate programs
True Keyed CW
Fully isolated CW keying output for direct keying of your rig's CW. This jack is for use with non-sound card software using serial DTR control.
Fully isolated FSK keying output for direct keying of your rig's FSK jack. This jack is for use with non-sound card software using serial TXD control
Maximum Mic/Keying/Audio Flexibility
Four ways to connect the receive audio from your radio: direct, mic jack, line out, speaker out. A radio speaker loop jack is included
Dual rear panel RCA PTT jacks provide for a foot switch, amplifier and sequencer
Front panel audio drive control allows setting the transmit audio from the computer to your radio without fumbling with your mouse
Your microphone may be bridged to computer as well as radio for on-the-fly digital recording
Transmit speech processing is done by looping mic. audio through the sound card using appropriate EQ and compression software. Voice Shaper by VE3NEA is an amazing free program for this
Plug in 2nd mic. jack allows instant automatic switch over to a headset mic. without unplugging your main mic
Both 1/4" and 1/8" front panel headphone jacks to monitor computer receive and transmit audio; no searching for adaptors. These connections facilitate using DSP receive audio software
Computer speaker PTT activated mute-on-transmit works with speech processing and for general sound card operation
PTT override and interrupt enables mic to override the computer or stop the computer program, perfect for contesting or SSTV operation
Front panel LED indicators show whether computer audio or mic. audio is routed to the radio
Front panel LED indicator shows if the computer audio is present at an adequate level for transmit or receive
Front panel LED indicators show PTT, CW and FSK activation status making it easy to check the operation of your software
Construction
Assembled in USA to IPC-610 manufacturing standards.
Printed circuit board uses FR4 material, double sided, plated through holes, solder mask over bare copper, silk screened
Enclosure: .062 aluminum, polyurethane painted, silk screen labeling front and back
3M Bumpon™ protective feet and 3M™ adhesive pads are provided for mounting
Toggle switches: 50,000 make and break cycles, 2 amps 250 VAC
Stainless steel hardware throughout including PEM™ threaded mounting standoffs
Amatørradio, Digimodes, ICOM, Yaesu, Kenwood
NB: Knappen for å vise hele beskrivelsen har kun en visuell effekt.
Brukerprofil
Du må være logget inn for å se brukerprofiler og sende meldinger.
Logg innAnnonsens metadata
Sist endret: 3.12.2025 kl. 10:38 ・ FINN-kode: 440181080
