Bildegalleri
(1/14)
LAUNCH X431 PRO ELITE Car Diagnostic Tools Auto OBD2 Scanner All System
Til salgs
Fiks ferdig
7 900 kr
Frakt fra 39 kr + Trygg betaling 214 kr
Trygg handel med Fiks ferdig
Varen sendes til deg, og du har 24 timer til å inspisere den før pengene overføres til selgeren.
Beskrivelse av varen
Tilstand: Som ny - Ikke synlig brukt
Original LAUNCH X431 PRO ELITE Bil Diagnostic
Som ny lite brukt. Sist oppdatert 10.2025
LAUNCH X431 PRO ELITE CAN FD DOIP All System Car Diagnostic ECU Coding
LAUNCH X431 PRO ELITE comes with Full Bi-directional Control, ECU/ Online Coding, 32+ Services, All Systems Diagnostics, FCA AutoAuth, CANFD DOIP, For VAG Guide, Refresh Hidden Functions, Auto Vin, Remote Control, 10,000+ Vehicle Coverage, 25 languages, 8 Extension Modules Supported (TPMS, XPROG 3, olliscope ...)
LAUNCH X431 PRO ELITE supports for Volkswagen/ Audi, the following function need Guided Function
√ Service Regeneration,Particle Filter(DPF)
√ Adapt Injector Correction Value
√ Reset Engine Control Adaptation Values
√ Throttle Learning
√ Fill Coolant Circuit
√ Adapt Values,SCR system
√ Activating/ Deactivating Cruise Control System
√ Basic Setting Of Transmission
√ Basic Setting of Sensors (-G85/-G200/-G201/-G251)
√ Basic Setting/ Bleeding Brake System
√ Initial A/C Compressor Run-In
√ Adaptation Automatic Locking At 15 km/h
√ Distance Control System Calibration
√ Deactivate Or Activate Airbags And Belt Tensioners
√ Adaptation Menu Key Multifunction Steering Wheel
√ Adapting Service Intervals
√ Service Interval Display ,Resetting
√ Transport Mode, Switching Off/On
√ Level Control System Basic Settings
√ Brake Pad Change
√ Headlight Beam Adjustment
√ Battery Adaptation
√ Rear View Camera System Calibration
√ Driver Assistance Systems Front Sensor System Calibration etc.
1. Oil Reset Service
2. Electronic Parking Brake Reset
lt needs to be performed in the following cases:
1.The brake pad and brake pad wear sensor are replaced.
2.The brake pad indicator lamp is on.
3.The brake pad sensor circuit is short, which is recovered.
4.The servo motor is replaced.
3. ABS Bleeding
This function allows you to perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS).
lt needs to be performed in the following cases:
1. When the ABS contains air.
2. When the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced.
4. Gear Learning
This function enables you to perform tooth learning for the car, to turn off the MIL.
lt needs to be performed in the following cases:
1. After the engine ECu, crankshaft position sensor, or crankshaft flywheel isreplaced.
2. The DTC 'tooth not learned' is present.
5. IMMO Service
This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remotecontrol keys to normally use the car.
lt needs to be performed in the following cases:
When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced.
6. Injector Coding
This function enables you to write injector actual code or rewrite code inthe ECU to the injector code of the corresponding cylinder, so as to more accurately control or correct cylinder injection quantity.
lt needs to be performed in the following cases:
After the ECu or injector is replaced.
7. Battery Maintenance System Reset
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will becleared and battery matching will be done.
lt needs to be performed in the following cases:
1. The main battery is replaced.
2. The battery monitoring sensor is replaced.
8. Diesel Particulate Filter (DPF) Regeneration
This function enables you to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.
lt needs to be performed in the following cases:
1. The exhaust back pressure sensor is replaced.
2. The PM trap is removed or replaced.
3. The fuel additive nozzle is removed or replaced.
4. The catalytic oxidizer is removed or replaced.
5. The DPF regeneration MlL is on and maintenance is performed.
6. The DPF regeneration control module is replaced.
9. Electronic Throttle Position Reset
This function enables you to make initial settings to throttle actuators and returns the learned values stored on ECU to the default state. Doing so can accurately control the actions of regulating throttle (or idle engine) to adjust theamount of air intake.
10. Gearbox Matching
This function enables you to complete the gearbox self-learning to improve gear shifting quality.
lt needs to be performed in the following cases:
When the gearbox is disassembled or repaired.
11. AFS (Adaptive Front-lighting System) Reset
This function enables you to initialize the adaptive headlamp system.
12. Sunroof Initialization
This function enables you to set the sunroof lock off, closed when it rains, sliding /tilting sunroof memory function, temperature threshold outside the caretc.
13. Suspension Calibration
This function enables you to adjust the height of the body.
lt needs to be performed in the following cases:
1. When replacing the body height sensor, or control module in the air suspension system.
2. When the vehicle height is incorrect.
14. EGR Adaption
This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.
15. Seats Calibration
This function is applied to match the seats with memory function that are replaced and repaired.
16. Tyre Reset
This function is used to set the size parameters of the modified or replaced tire.
17. Coolant Bleed
Use this function to activate the electric water pump before venting the cooling system.
18. AdBlue Reset (Diesel Engine Exhaust Gas Filter)
After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.
19. NOx Sensor Reset
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) inengine exhaust. lf the NOx fault is re-initialized and the NOx catalytic converteris replaced, it is necessary to reset the catalytic converter learned value storedin the engine ECu.
20. AC System Initialization
AC system relearn/initialization must be performed when the vehicle AC ECUador actuator is replaced or the ECu memory is lost.
21. High Voltage Battery Detection
This function is used for high voltage battery diagnosis and status information detection.
22. Windows Calibration
This function is used to perform door window matching to recover the ECu initial memory, and recover the automatic ascending and descending function of power window.
23. Language Change
This function is used to change system language of vehicle center console.
24. AF Reset
This function is applied to set or learn airlfuel rate parameters.
25. Stop/ Start Reset
This function is used to open or close the automatic Start Stop function via setting the hidden function in ECU.
(The precondition is vehicle equipped with hidden function and hardware support).
26. Intelligent Cruise Control System Reset
This function is used to matching the intelligent cruise control module after it isreplaced or repaired.
27. TPMS Reset
When due to the tire pressure is too low,tire leaks,tire pressure monitoring device is replaced or installed,tire is replaced and tire pressure sensor is damaged,The tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL.
28. Transport Mode
To lower vehicle power consumption, user may perform the following operations: limit vehicle speed, not wake up the network for door open and disable remote key etc. In this case, deactivating transport mode is needed torecover vehicle being normal.
29. Engine Power Balance Monitoring
This function is used to monitor crankshaft acceleration in the power stroke ofeach cylinder, to determine the relative power provided by each cylinder.
30. Gas Particulate Filter (GPF) Regeneration
This function is used to perform the GPF replacement or regeneration after the fuel consumption is increased and engine output power is reduced resultingfrom a long time service of the GPF.
31. RESET PROGRAM (Extended function)
All system diagnostic function
This LAUNCH diagnostic scanner can establish a data link to all systems and subsystems of the vehicle being serviced to:
- Retrieve ECU information of the tested control units including unit type, version numbers, and other specifications, etc.
- Read & erase DTCs to locate problem areas and clear the codes.
- View Live Data of each parameter item.
The following is a list of modern vehicle systems that this scan tool can get access to:
- Engines / Auto Transmission / Airbags / Immobilizer / Key Coding / ABS / Cruise Control / Instruments / Self Leveling Suspension systems
- Seats / Doors / Gateway / Steering Angle / Air Suspension / Body Systems / Electronic Power Steering & Motor Assisted / Power Steering / Tyre Pressure / Rain Sensors / 4WD System
- Stabilizer / Intelligent Parking Assist/Door Motors / Audio Systems / Air Conditioning / Tiptronic / Anti Theft / Soft Top / Headlamp Leveling / Central Locking / Automatic Clutch / DPF Reset
- Electric Windows / Plip Programming / Heated Rear Window / Xenon Headlights / Wash Wipe / Fuel Burning Heater / Transfer Box / Seat Memory / Oil Life Service Reset / Sliding Doors / Electronic Throttle
- Navigation System / Rollover Sensor / Cruise Control / Multi Function Steering Wheel / Aux Heating / Electronic Parking Brake / Clutch Electronics ... and more.
This comprehensive scanning process is able to locate the faulty systems and retrieve the DTCs related easily. So you can work on all parts of the vehicle systems to enhance the performance, save energy, reduce emissions, and everything else.
The other Function of LAUNCH X431 PRO ELITE
1. Auto VIN Scan
2. 8-in-1 Live Data Stream
3. DTC Look up
4. Remote Diagnose Function
5. Diagnostic Report
6. Diagnostic Report print & Share
7. Online Repair Sources
8. MALL Function: you can subscribe the new vehicles directly .
NB: Knappen for å vise hele beskrivelsen har kun en visuell effekt.
Brukerprofil
Du må være logget inn for å se brukerprofiler og sende meldinger.
Logg innAnnonsens metadata
Sist endret: 5.12.2025 kl. 00:32 ・ FINN-kode: 436261253
